![]()
On Screen 4 of 4 in the Maintenance Mode Wizard, click Finish to restart the system and apply the generic and default database. If your time format preference is a 24-hour clock, From the Time panel, select the Hour: (0–23), Minute: (0–59), and Second: (0–59) from the pull-down menus. You must also specify am or pm by selecting one of the radio buttons. If your time format preference is a 12-hour clock, from the Time panel, select Hour: (0–12), Minute: (0–59), and Second: (0–59) from the pull-down menus. This screen allows you to choose your preference for time format, either a 12-hour clock or a 24-hour clock. You can provision the time format display for your WaveStar ® CIT from the Network View by selecting View → Preferences and clicking the Display tab. This screen picks up the time format preference from the WaveStar ® CIT. Step 3), the title bar of the Maintenance Mode Wizard displays either DMXtend 4.0, DMXtend 5.0, DMXtend 5.1, DMXtend 8.0, DMXtend 9.0, or DMXtend 9.1. #Download networkview full version code#Screen 1 of 4 in the Maintenance Mode Wizard appears.ĭepending on the boot code of your SYSCTL (refer to To preserve the security of your equipment, it is highly recommended that you change all three logins and passwords during your first session after completing this initial installation procedure. #Download networkview full version password#LUC01, LUC02, and LUC03 are the default privileged User IDs, and DMXTND2.5G is the default privileged password for Alcatel-Lucent 1665 DMXtend. Pushing the UPD/INIT button while in Maintenance Mode has no effect.īecause the shelf is in Maintenance Mode, your logins and passwords are default.Įnter the following in the NE Login Dialog window (login information is case sensitive) to log in to the NE: Repair the problem generally caused by bent pins and repeat this procedure.Ī red, four-segment square (2 x 2) appears in the IND display on the LNW2 SYSCTL.Īcknowledges the UPD/INIT button was momentarily pushed. LNW2 SYSCTL does not boot due to unexpected or unreadable shelf type. Replace the indicated NVM or find another LNW2 SYSCTL equipped with two factory-installed NVMs and repeat this procedure. “x” indicates that the NVM socket (1 or 2) is empty or the NVM installed is failed. Unseat the LNW2 SYSCTL and repeat this procedure, properly seating the faceplate latch. LNW2 SYSCTL faceplate latches are not fully seated. ![]() No compatible generic on the NVMs in the LNW2 SYSCTL.įind another LNW2 SYSCTL equipped with two factory-installed NVMs and repeat this procedure or contact your next level of support. Check to make sure they are properly seated and repeat this procedure. #Download networkview full version install#Install two Alcatel-Lucent-supplied NVMs in the LNW2 or find another LNW2 SYSCTL equipped with two factory-installed NVMs and repeat this procedure. ![]() ” (“.” is a red, four-segment square representing a period) and 1įind another LNW2 SYSCTL equipped with two factory-installed NVMs and repeat this procedure. ” (“.” is a red, four-segment square representing a period) and 0Īlternating M and P and 9 and “. ” (“.” is a red, four-segment square representing a period) and 1Īlternating M and P and 8 and “. ” (“.” is a red, four-segment square representing a period) and 0Īlternating M and P and 5 and “. Observe the IND display on the LNW2 SYSCTL the display indicates the state of the SYSCTL.Īlternating M and P and 4 and “. While the CR LED is flashing, the MJ, ABN, and NE LEDs light and remain lighted. The ACTIVE LED lights and remains lighted and the CR LED flashes 10 times. ![]() The FAULT LED remains lighted for approximately another 20 seconds and then extinguishes. The b continues flashing for approximately 75 seconds and the IND display is blank. After approximately 10 seconds, a flashing b appears in the IND display on the SYSCTL, indicating that a boot is in progress. The FAULT LED lights and remains lighted for approximately 90 seconds. The LNW2 SYSCTL exhibits the following visible cycles during initialization: Allow a few minutes for the pack to complete initialization. Insert the LNW2 (SYSCTL) circuit pack into the slot labeled CTL in the center of the shelf using a steady pressure on both faceplate latches. Step 3 for the complete listing of codes and required actions. If both NVM sockets are empty, the IND displays an alternating E and 0 and 1. If one NVM socket is empty or an NVM is failed, the IND displays an alternating N and O and x (x=1 or 2, indicating the offending NVM socket). #Download networkview full version software#For software installation, ensure that two NVMs are present in the LNW2 SYSCTL.Īfter the LNW2 is installed, if one or both NVMs are missing, NVM removed alarm(s) are issued and: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |